Gyeon Q² Pure is a user-friendly quartz coating that simultaneously protects and enhances the appearance of automotive paint. Developed in South Korea, Gyeon Q² Pure uses the latest in low volatile content silicon (Si) technology to lay down a film of pure siloxane polymers that condense rapidly to form a fully crystallized SiO2 coating that bonds to painted surfaces at the molecular level. Unlike many coatings, Gyeon Q² Pure contains no alcohol and therefore doesn’t flash off rapidly, which makes the application process much easier. On the other hand, Gyeon Q² Pure features an SiO2 content of more than 50%, which is considerably higher than that found in many rival products. This results in it adding, on average, one grade of hardness (1H) on the pencil hardness scale to the scratch resistance of the underlying paint, which helps to greatly retard the rate at which wash marring accumulates.
As a result of being coated with a smooth, dense layer of crystallized SiO2, treated surfaces become extremely hydrophobic (water-hating), which causes rainfall and rinse water to bead up and roll off very quickly. This extreme beading not only looks good but also tends to pick up and carry away fresh contaminants, which makes routine washing easier and much safer. In addition to these benefits, Gyeon Q² Pure also provides excellent protection against bird droppings, bug splatter, road salt, and harmful UV radiation for up to eighteen months, even on daily drivers (it is virtually impervious to cleaning chemicals and pressure washing). Gyeon Q² Pure is currently supplied as a pre-packed kit containing either a 30 ml, 50 ml, or 100 ml bottle of Gyeon Q² Pure, a 100 ml bottle of Gyeon Q²M Cure, a Gyeon Q²M Applicator Block, four Gyeon Q²M Applicator Suedes, and an instruction booklet.
You should apply Gyeon Q² Pure in a dry place out of direct sunlight. In all cases, prepare the surfaces you are going to treat in the normal way (wash > decontaminate > polish), and then do a wipe down with Gyeon Q²M Prep to ensure that they are spotlessly clean. Next, wrap one of the supplied Gyeon Q²M Applicator Suedes around the supplied Gyeon Q²M Applicator Block and lightly wet one end of it with Gyeon Q² Pure using the supplied dropping pipette. Then spread the coating quickly over the first panel, using light pressure and overlapping strokes. After 20-30 seconds, and without adding any more product, rub the Gyeon Q²M Applicator Suede over the panel in tight circles, using moderate speed and pressure. This step is critical, as it levels the coating and makes it easy to remove. You must then buff off the remaining residue as quickly as possible, i.e. before it begins to harden. Buffing off is best accomplished with a Buffing Towel using moderate speed and pressure in order to fully remove the residue and reveal an intense streak-free shine. Using a bright light, check the panel carefully for smears and remove them before moving on; failure to remove smears fully can result in them hardening to the point of being impossible to remove without machine polishing, so make sure you are thorough!
After all panels are treated you must then leave the car in a dry place out of direct sunlight for a minimum of 24 hours to allow the SiO2 coating to harden (if you wish, you can accelerate this process by heating the treated panels to 60°C for 10 minutes using an infra-red heat lamp). Finally, to reduce the risk of water spots forming while it continues to cure (full curing takes around 14 days to achieve), you should apply a protective topcoat of Gyeon Q²M Cure (you should also avoid washing the car with any kind of detergent for the first 7 days). Please note that you must discard all used applicators and towels after you’ve applied Gyeon Q² Pure, because it hardens massively as it cures, forming a residue that has the potential to inflict severe marring or worse if applicators and towels are re-used. Furthermore, after each use, you must also replace the dropping pipette with the air-tight cap, and then wash out the pipette with hot water. Failure to follow these steps will result in any leftover product setting solid in the bottle and the pipette, rendering them unusable in the future.